The Bell RS7C LTWT Carbon Helmet is an ultra-lightweight version of the RS7 Carbon combining an aerospace-grade carbon shell, reinforced energy-absorbing liner system and the performance features of the HP7. This results in the most advanced, lightweight Snell 2020 helmet currently offered. The RS7C LTWT weighs less than 2.795 pounds.
- Ultra-lightweight
- Natural Carbon finish
- Weighs less than 2.795 pounds
- Uses SE07 shields
- Snell SA2020
- FIA approved
| Brand | Bell |
| Product Line | RS7C LTWT |
| Open/Closed Face | Closed |
| Fresh Air | No |
| Vent System | Yes |
| Snell Rating | SA 2020 |
| FIA Approved | Yes |
| Head and Neck Support Ready | Yes |
| Shield Included | Yes |
| Shield Color | Clear |
| Visor Included | No |
| Graphics | No |
| Bag Included | Yes |
| Material | Carbon Fiber |
| Color | Natural |
| Finish | Clearcoat |
| Quantity | Each |
Sizes available:
| MPN | Size |
| 1237A05 | 7-1/8- (57- cm) |
| 1237A06 | 7-1/8 (57 cm) |
| 1237A07 | 7-1/4 (58 cm) |
| 1237A08 | 7-3/8 (59 cm) |
| 1237A09 | 7-3/8+ 59+ cm) |
| 1237A10 | 7-1/2 (60 cm) |
| 1237A11 | 7-5/8 (61 cm) |
| 1237A12 | 7-5/8+ (61+ cm) |
Bell Helmet Size Chart
| Size | Hat Size | Inches | Centimeters |
|---|---|---|---|
| 4XS | 6 3/8 | 20 1/16 | 51 |
| 3XS | 6 1/2 – 6 5/8 | 20 1/2 – 20 7/8 | 52-53 |
| 2XS | 6 3/4 – 6 7/8 | 21 1/2 – 21 5/8 | 54-55 |
| XS | 7 | 22 | 56 |
| S | 7 1/8 | 22 3/8 | 57 |
| M | 7 1/4 – 7 3/8 | 22 3/4 – 23 1/4 | 58-59 |
| L | 7 1/2 | 23 5/8 | 60 |
| XL | 7 5/8 – 7 3/4 | 24 – 24 3/8 | 61-62 |
| 2XL | 7 7/8 – 8 | 24 3/4 – 25 1/4 | 63-64 |
| 3XL | 8 1/8 – 8 1/4 | 25 5/8 – 26 | 65-66 |
| 4XL | 8 3/8 – 8 1/2 | 26 3/8 – 26 3/4 | 67-68 |
Fitting your Bell Helmet
Proper helmet fit is vital to the performance of a helmet during an impact. For maximum protection the helmet must fit properly with the chin strap securely fastened and provide adequate peripheral vision.
Measuring the head is only a starting point for the entire sizing procedure. Due to varying shapes, heads that are apparently the same size when measured by a tape may not necessarily fit the same size helmet. A small metal tape measure or a cloth tape may be used to make your initial measurement. You can also use a string, which can then be laid against a measuring tape.
The circumference of the head should be measured at a point approximately one inch above the eyebrows in front, and at a point in the back of the head that results in the largest possible measurement. Take several measurements. The largest measurement is the one you want to try on first. If you use a balaclava or head sock, always measure and fit the helmet with it on. Use the Bell sizing chart to determine the size that best matches the head measurement.
